Building tomorrow's careers in Electronics and Computer Control... One step at-a-time.
|
|
|
|
|
Home  Industrial Products Elexol |
|
|
|
EDB - Ethernet Digital I/O Board (Ether I/O 24)
|
|
24 Channels of Digital I/O on Ethernet Networks
The EDB board (Elexol Ether I/O 24 R) is a versatile platform for controlling external
circuits and
devices through an Ethernet network. The board provides 24 individually
programmable I/O channels for digital I/O, and is capable of wireless
operation with a wireless network router. It
comes complete with a host interface application program and a full
Windows API
(Application Program Interface) for programming in VB or VC++.
The module connects to any Ethernet network
supporting the TCP/IP protocol suite and
can communicate with any point on that network.
By connection with an Internet Router the
device can communicate with any Internet
connected device
A number of accessory products from Unistep are specifically
designed to work
with the EDB board and enhance its capabilities. Unique MAC address
assigned to each board makes it possible to have multiple boards on the
same network.
EDB Board (Ether I/O 24 R). . . . . . . . . EDB-AB-010 $114.90 USD |
EDM - Ethernet Digital I/O Module (Ether I/O 24 DIP)
|
 |
Development module for 24-Channel digital I/O on Ethernet networks.
The EDM (Elexol P/N Ether I/O 24 DIP) is an integrated, micro-controller based network interface
board with 24 digital user I/O lines. The module’s firmware and hardware enable
your devices or other modules to be connected to a generic Ethernet network and
controlled using a command sent over the network via UDP.
Each of the 24 User
I/O lines operates at 5V DC maximum levels and can be independently programmed
as an input whose state can be remotely sensed via another network device, an input
whose state is internally checked and transmitted when a change occurs, or an
output whose state can be remotely controlled by another networked device.
The outputs of the
module are able to source or sink up to 30mA per I/O, up to a maximum 50mA per port,
to allow for direct connection to a variety of external devices
EDM Development Module (Ether I/O 24 DIP). . . . EDM-DM-010 $112.90 USD |
UDB - USB Digital I/O Board (USB I/O 24)
|
 |
24 Channels of Digital I/O on the USB Bus.
The
UDB board is a versatile platform for controlling external circuits and
devices through the USB ports. The board provides 24 individually programmable
digital I/O channels for digital I/O, and is capable of fast USB transfers. It
comes complete with a host interface application program and a full Windows API
(Application Program Interface) for programming in VB or VC++.
The
module features 24 5V level signal lines
individually programmable as input or output.
As the module connects to the USB
port, multiple modules can be connected
to a single PC by the use of a USB hub or
hubs. Each module features a serial
number and the PC can identify each module
uniquely allowing for multiple modules to
be connected for a single application.
The outputs of the module are able to source
or sink up to 30mA per I/O, up to a maximum
50mA per port, to allow for direct connection
to a variety of devices
UDB Board (USB I/O 24R). . . . . . . UDB-AB-010 $82.30 USD
|
UDM - USB Digital I/O Module (USB I/O 24 DIP)
|
 |
Development module for 24-Channel digital I/O on the USB bus.
The UDM module features 24 (8 x 3) 5V-level
signal lines individually programmable as input or output. Multiple modules can
be connected to a single PC by the use of a USB hub or hubs. Each module
features a unique serial number and the PC can identify each module separately,
thereby allowing multiple modules to be connected for a single application. The
outputs of the module can source or sink up to 30mA per I/O and up to a total maximum
of 50mA per port, to allow for direct connection to a variety of devices.
The module has the form factor of the
50 pin Dual Inline Package (DIP) and fits into a standard 50 pin 900mil wide IC
Socket. This makes the USB I/O 24 DIP ideal for rapid prototyping and development
work.
UDM Development Module . . . . . . UDM-DM-010 $97.60 USD |
AIO - Analog I/O Board |
 |
Eight (8) ADC and two (2) DAC channels for the UCP and IRP Modules.
The Analog I/O Board is an accessory board that provides
an analog interface to the USB and Ethernet/Internet Digital I/O (UDB and EDB, respectively). The board consists of an 8 channel 10 bit Analog to
Digital Converter (MCP3008) and a 12 bit Digital to Analog Converter with 2
buffered outputs (MCP4922).Communication to the A/D and D/A Converters is via the SPI
interface of the I/O 24 module which is already implemented in the firmware.
The 8 channels of the A/D, 2 channels outputs of the D/A,
and all the VREF voltages are brought to screw-type terminal blocks
for easy access. These terminal blocks will accept
cables 0.5 – 2mm thick. The connection between the I/O24 module and the Analog
I/O board is via an IDC link cable supplied with the board.
AIO Lab Module . . . . . . AIO-LM-010 $51.20 USD
AIO Board Only . . . . . . . AIO-AB-010 $39.50 USD |
ROB - Relay Output Board |
|
Output power enhancement for the UDB and EDB boards through eight (8) relay outputs.
8 relays with both N/O
and N/C contacts rated to 250V AC or DC at 5 Amps. It is possible to drive a
multitude of devices with these versatile relays. Each of the 8 relays on the
board has a matching LED to indicate its state.
The relay coils are
powered from an external 12V DC source but are individually controlled by the
buffered control signals from the I/O module. External power can be applied
either through the binding posts from a lab supply or through the DC power
connector from an AC/DC wall adapter.
ROB Lab Module . . . . . . ROB-LM-010 $81.80 USD
ROB Board Only . . . . . . ROB-AB-010 $59.80 USD |
IOC - I/O Combo Board |
 |
I/O enhancement
for UDB and EDB boards with relay outputs and isolated digital inputs.
The board contains 4 Relay Outputs and 4 optically
isolated input channels. The relay outputs have both Normally Open (N/O) and
Normally Closed (N/C) contacts rated to 250V AC or 30V DC, both at 5 Amps. The
relays’ coils are powered by an external 12VDC power supply that is capable of
producing approx 350mA (about 80mA is required per active relay). The power
supply is not provided with the board, but the Lab Module (‘LM’) version of the
board has binding posts in addition to the a 3.5 mm DC plug for easy supplying of the 12
V external power. The relay coils are controlled using the on-board ULN2003
driver via the I/O ports of the board. Each of the output port channels has an
LED to indicate the relay output status.
The input channels are bridged wet contacts which
are electrically isolated from all other channels and the I/O24 module. Each
input channel also has a LED to indicate when a signal is present on the
channel.
IOC Lab Module . . . . . . IOC-LM-010 $68.90 USD
IOC Board Only . . . . . . IOC-AB-010 $46.90 USD |
OIB - Opto Input Board |
 |
Input enhancement for the UDB and EDB I/O boards with eight (8) optically isolated input channels.
8 optically isolated
input channels to accept signals from 3-24V AC or DC. Each channel of the board
is electrically isolated from all other channels and the I/O module, thereby providing
isolated grounds to prevent incoming signals from interfering with each other
or prevent damage the I/O module.
The board has a box header matching the connector of the
I/O module. Each channel has an LED indicator to show the digital status.
OIB Lab Module . . . . . . . OIB-LM-010 $50.60 USD
OIB Board Only . . . . . . . OIB-AB-010 $38.60 USD |
ULN – ULN2803 Output Board (ULN2803 Switch Board)
|
 |
Output Power Enhancement with ULN2803 High Voltage-High Current Drivers for UDB and EDB
The I/O 24 ULN2803 Switch Board is an accessory
board that allows higher voltage and current devices to be interfaced to the
low level logic provided by the I/O24 modules USB and IRP. The board contains a
ULN 2803 IC and LED indicators to show channel Status.
The ULN2803 includes 8-bit
TTL-input NPN Darlington current sinks. Each driver can handle a maximum of
500mA continuous (when using a single channel only) and can withstand a maximum
50V in its off state. This makes the ULN2803 well suited to provide an
interface between the low logic level interfaces and higher current/voltage devices
such as relays, solenoids, motors and lamps.
ULN Lab Module . . . . . . . ULN-LM-010 $49.80 USD
ULB Board Only . . . . . . . ULN-AB-010 $27.80 USD |
CLB - Connector / LED Board |
 |
Terminal expansion board for the UDB and EDB boards
This board is designed
to facilitate easy connection of thicker wires to the I/O module or to provide
a buffered visual indication of the states of signals on one of the 8-bit
ports. This board can also be used as a status indicator board at a remote
location by a control application. The driver circuit and the indicators are
powered from the 5V supply on the I/O board.
CLB Lab Module . . . . . . CLB-LM-010 $38.50 USD
CLB Board Only . . . . . . . CLB-AB-010 $27.80 USD |
PSB - Push-Button / Slide Switch Board |
 |
Input enhancement for the UDB and EDB I/O boards with push-button and slide switches.
This board is intended
as a convenient input signal generation circuit to facilitate testing,
debugging and troubleshooting while developing applications or other control
devices. The board features 8 miniature tactile push-button switches and 8
slide switches.
Each of the 8 input
channels has an indicator LED to show that the board is powered and the
push-button switch or the slide switch is activated.
PSB Lab Module . . . . . . . PSB-LM-010 $49.40 USD PSB Board Only . . . . . . . PSB-AB-010 $37.40 USD
|
UDF - USB Dual Channel UART/FIFO Module (USBMOD5)
|
 |
Development module for painless USB-UART/FIFO functionality
The
USBMOD5 is a integrated module based
on the FTDI FT2232C Dual Channel USB
UART / FIFO IC. The module features
two Multi-purpose UART/FIFO controllers
that can be configured in several
different modes depending on the application.
More Info (http://www.elexol.com/DevelopmentMods/USBMOD5.php)
UDF Development Module (Elexol USBMOD5). . . . . UDF-DM-010 $39.80 USD |
|
|
|
|
Copyright (c) 2011 Unistep Technologies.
|
|
|
|
|
|
